Search found 12 matches
- Mon Jun 11, 2018 8:57 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Mach3 or Mach4
- Replies: 8
- Views: 6755
Re: Mach3 or Mach4
They sterilized the motors. Stickers removed. But I’ll have to check dimensions to verify nema. Thank you. I’m looking to keep the shark pretty much intact and put a new controller on it. Would like to do a setup that I can upgrade a home built onto later. That way I can put the shark back together ...
- Mon Jun 11, 2018 7:27 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Mach3 or Mach4
- Replies: 8
- Views: 6755
Re: Mach3 or Mach4
I have been looking at putting Mach4 on my machine. And I have figured out that we need to use a completely different controller. I have been pulling teeth to find out from Nextwave as to what hardware they are using. They finally answered with. Hi Mr. Devlin, We use NEMA 23 Bipolar stepper motors. ...
- Mon Feb 26, 2018 10:44 pm
- Forum: Show off your CNC Shark projects
- Topic: Devlin crest
- Replies: 0
- Views: 3823
Devlin crest
Created with aspire
- Mon Feb 26, 2018 10:42 pm
- Forum: Show off your CNC Shark projects
- Topic: Created with aspire.
- Replies: 1
- Views: 2700
Created with aspire.
Created with aspire
- Tue Feb 20, 2018 10:26 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Shark laser specs
- Replies: 2
- Views: 2914
Re: Shark laser specs
Thanks.
- Mon Feb 19, 2018 9:14 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Shark laser specs
- Replies: 2
- Views: 2914
Shark laser specs
Ok I have the laser... it works and I’ve done a test burn. Are there any specs on this laser so we can get comparison info as to what it will do. Can it cut and if so how much. I’m sure it’s not much or needs many passes. How many watts is it. Type of laser. Diode I guess.
- Fri Feb 09, 2018 1:46 am
- Forum: CNC Shark Pro Plus HD
- Topic: Shark Tanks, Dust, Indoor or Outdoor Shop
- Replies: 6
- Views: 6966
Re: Shark Tanks, Dust, Indoor or Outdoor Shop
I am new. But I do run the brush with a vacuum. I also have running overhead a 500 cfm dust collector. I am thinking of building a table with a cage for the cnc. I would attach the dust collector to the side and use it as a downdraft system. I would have inlet holes on the far side of the box. No he...
- Fri Feb 09, 2018 1:02 am
- Forum: CNC Shark Pro Plus HD
- Topic: 3d vcarve has line that is not in preview
- Replies: 2
- Views: 3928
Re: 3d vcarve has line that is not in preview
Hmmm. That was my solution. Stay off the machine....
- Fri Jan 26, 2018 5:11 pm
- Forum: CNC Shark
- Topic: How does PAUSE work
- Replies: 14
- Views: 8462
Re: How does PAUSE work
My wife has a Bernina embroidery machine. If the needle or thread breaks I can stop and fix the problem. Then I can reset the position back to where the problem occurred and continue the job. When I asked tech support about this with the shark they said it was on their todo list!!!
- Sun Jan 14, 2018 9:53 am
- Forum: CNC Shark
- Topic: Bosch 1617 collets
- Replies: 5
- Views: 4892
Bosch 1617 collets
Suggestions on a 1/8” collet for a Bosch 1617 router. Or should I waste my time with 1/8” shank bits.