Search found 18 matches
- Mon Sep 17, 2012 5:45 am
- Forum: Shark Pro Plus
- Topic: Table coupler
- Replies: 5
- Views: 4574
Re: Table coupler
Thanks Rodger, Not much room under the table for stiffeners ,have looked at that, suppose I could lift the table a little and loose some height capacity. Another option I am considering is a 10- 12 mm thick aluminium platen table about 400mm square with a heap of tapped holes for clamping . I have t...
- Mon Sep 17, 2012 4:31 am
- Forum: Shark Pro Plus
- Topic: Table coupler
- Replies: 5
- Views: 4574
Table coupler
Hi all,
Anybody know if a coupler exists for the Pro Plus individual aluminium boards on the table? I think it would add to rigidity quite alot. Thought I would ask before I consider machining some up.
Anybody know if a coupler exists for the Pro Plus individual aluminium boards on the table? I think it would add to rigidity quite alot. Thought I would ask before I consider machining some up.
- Mon Sep 03, 2012 7:01 am
- Forum: Shark Pro
- Topic: Router Runout
- Replies: 1
- Views: 3321
Router Runout
Hello forumers, I have been thinking about this post for a few days but I thought it might be an idea to see if any body else has had problems , checked the topic on the forum and geez it reads like a telephone book .I have had suspicions of the router for a while,it was too noisy, out of balance so...
- Sat Sep 01, 2012 9:51 pm
- Forum: Shark Pro
- Topic: Dodgy `Y` axis The continuing saga
- Replies: 2
- Views: 3716
Re: Dodgy `Y` axis The continuing saga
Hello Wolffie, Working on a post regards the router , next day or so. Have seen your return post on the Vectric forum, will respond soon. jcatcmc
- Sat Sep 01, 2012 7:01 am
- Forum: Shark Pro
- Topic: Dodgy `Y` axis The continuing saga
- Replies: 2
- Views: 3716
Dodgy `Y` axis The continuing saga
Hello again, Continuing on from my previous posting regards my `Y` axis drive problems I had a couple of good days out of it then the motor started locking up in the high speed parts of the toolpath ( lucky only trial runs this time) had the bare motor out on the bench less the screw and it would on...
- Fri Aug 31, 2012 4:12 am
- Forum: Shark Pro
- Topic: Dodgy `Y axis Post # 1
- Replies: 0
- Views: 3511
Dodgy `Y axis Post # 1
Hello All, Been having a few Shark Pro problems of late so will tackle them one post at a time. Just starting some serious work with it some 15 months after purchase ( probably 10-12 hours on it )noticed some long flutes really rough at one end also unit would stall on high speed jog, a bit of looki...
- Sun Jun 26, 2011 4:31 pm
- Forum: CNC Shark
- Topic: Dead controller?
- Replies: 3
- Views: 3779
Re: Dead controller?
Thanks for the reply Joe, Since my last post and as my trade is electrical I delved a bit deeper into the control box and found the slide switch on the power card set to 115 volts ( U.S. ) not too good for my 230 Australian volts. I set that right and replaced the blown fuse on the card and powered ...
- Sat Jun 25, 2011 5:38 pm
- Forum: CNC Shark
- Topic: Dead controller?
- Replies: 3
- Views: 3779
Dead controller?
It is now 2 weeks since I set up my new Shark Pro Plus and it hasn`t fired a shot yet. The control box appears to be dead as a dodo. My dealers response to the problem hasn`t been actually awe inspiring, ( He`s lucky he`s over a thousand miles away so a bit hard to throw through his window ) Initial...