Search found 208 matches
- Sat Jan 19, 2013 7:59 am
- Forum: System Comparisons
- Topic: THE NEW MAKO IS HERE!!!
- Replies: 188
- Views: 166803
Re: THE NEW MAKO IS HERE!!!
EdThorne, Tonydude The answers to your questions about the Mayan calendar bit = 0.50 V bit paint = Rust Oleum Hammered Metal Gold Must allow 24-48 hours to dry befor stain stain = Ruet Oleum wood stain color = Kona (almost black) In the link it called for a gell stain but I was unable to find any lo...
- Fri Jan 18, 2013 6:35 am
- Forum: System Comparisons
- Topic: THE NEW MAKO IS HERE!!!
- Replies: 188
- Views: 166803
Re: THE NEW MAKO IS HERE!!!
4dThinker This is my stop gap to deal with the gantry sag. I also found you can add paper shims in the center between the gantry and the board to correct the sage so you have the same cut depth in the center as the sides It can make a big differenc if you are cutting a large area with a lot of detail.
- Sat Jan 12, 2013 10:43 am
- Forum: Setting up the Shark
- Topic: 2 bits; 4 bits; 6 bits; a dollar
- Replies: 4
- Views: 4272
Re: 2 bits; 4 bits; 6 bits; a dollar
Ohiococonut
The .0625 ball nose would be for a finish cut only. I should have also included a 0.125 ball nose which would get much more use than a 0.0625. Sorry Mike
The .0625 ball nose would be for a finish cut only. I should have also included a 0.125 ball nose which would get much more use than a 0.0625. Sorry Mike
- Sat Jan 12, 2013 8:26 am
- Forum: Shark Pro Plus
- Topic: Name Inlay
- Replies: 10
- Views: 8660
Re: Name Inlay
Mike Some may want to do the male cut first. That way you can test fit the mail into the female pocket befor you remove the female from the table and maybe lose your zerro setting. If the female pocket is to small you can set zerro a few hundreds of an inch lower and recut the female. This is what I...
- Fri Jan 11, 2013 4:28 pm
- Forum: Setting up the Shark
- Topic: 2 bits; 4 bits; 6 bits; a dollar
- Replies: 4
- Views: 4272
Re: 2 bits; 4 bits; 6 bits; a dollar
Mike I have never bought any bits from centuriontools befor but I do belive I have seen post here and also the Vectric fourm were other members have. To start you are going to need 1 90 dig 0.50 dia V bit 1 60 dig 0.05 dia V bit 1 0.25 dia Up Cut end mill 1 0.25 dia Down cut end mill 1 0.0625 Up Cut...
- Wed Jan 09, 2013 6:55 am
- Forum: Shark Pro
- Topic: New bed on an old shark pro
- Replies: 16
- Views: 16033
Re: New bed on an old shark pro
Wolffie
This is one way I have used I just took a SWAG at the dia of the bolts. The one thing to keep in mind is you need to be able to drop the T bolt through the round hole BUT the head of the T Bolt sould not be able to spin a round once it is in the track. Cut with a 0.25 EM
This is one way I have used I just took a SWAG at the dia of the bolts. The one thing to keep in mind is you need to be able to drop the T bolt through the round hole BUT the head of the T Bolt sould not be able to spin a round once it is in the track. Cut with a 0.25 EM
- Tue Jan 08, 2013 5:37 pm
- Forum: Software. Programming
- Topic: rounding corners
- Replies: 5
- Views: 3333
Re: rounding corners
adowty If the board you are cutting does not look like 3d preview something is wrong. The big question is what is wrong. I would like to see the photo for the first problem to get a better idea what you are doing, also were you using an EM bit ? As far as the second problem are you sure the router i...
- Sat Jan 05, 2013 6:28 am
- Forum: Setting up the Shark
- Topic: What I needed to know to buy in.
- Replies: 8
- Views: 5333
Re: What I needed to know to buy in.
Brittell Your way ahead of all of us. A year ago when many of us got our Shark the manual was not as good as the one you got with a toilet seat you bought at Home Depot. As far as it is online and you need to down load it that is the way every big company is going. Well with that said welcome to the...
- Fri Jan 04, 2013 8:27 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Set up and leveling Shark Pro HD
- Replies: 10
- Views: 19117
Re: Set up and leveling Shark Pro HD
Still more photo for above
- Fri Jan 04, 2013 8:23 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Set up and leveling Shark Pro HD
- Replies: 10
- Views: 19117
Re: Set up and leveling Shark Pro HD
More photos for above