Version 1.4.0.10 was upload today which has a fix for the load error seen on some computers with certian types of SD cards.
Tim
Search found 355 matches
- Wed Aug 25, 2010 9:02 pm
- Forum: Software. Programming
- Topic: Is there new Shark Software???
- Replies: 9
- Views: 7762
- Tue Aug 24, 2010 10:07 pm
- Forum: Shark Pro
- Topic: Mach 3 Compatible?
- Replies: 9
- Views: 11676
Re: Mach 3 Compatible?
The Shark Pro Plus does not use the same control boards as the other Sharks. As a note. As for using the probe software and mach 3, the problem might not have anything to do with the drivers and might be an issue with firmware update to work with the probe. are you saying that you can use the cnc sh...
- Sun Aug 22, 2010 9:02 pm
- Forum: Show off your CNC Shark projects
- Topic: Cabinet Door
- Replies: 0
- Views: 5024
Cabinet Door
Here is a cabinet door I did for a show example.
I thought it turned pretty well so I thought I would share.
I got the door from a cabinet maker, carved it then gave it back to him so it could be finished.
I am not a huge fisherman but I loved the saying.
I thought it turned pretty well so I thought I would share.
I got the door from a cabinet maker, carved it then gave it back to him so it could be finished.
I am not a huge fisherman but I loved the saying.
- Sun Aug 22, 2010 8:41 pm
- Forum: Shark Pro
- Topic: Getting more Z
- Replies: 6
- Views: 7053
Re: Getting more Z
There are 2 quick/easy ways to get more height in the Z without having to modify the machine. One is you can loosen the Router clamp and slide it up to give you some more height. The second is you could move the side gantry up one notch with the 12 bolts on the side. You would only have 8 bolts hold...
- Sun Aug 22, 2010 8:35 pm
- Forum: Software. Programming
- Topic: Load error
- Replies: 17
- Views: 20272
Re: Load error
We are working with James to resolve the issue by trying an older software controller on his machine. The newer controllers 1.4.0.9 have the ability to use high capacity cards which have a faster speed of communication. We have only seen a load error with a bad card so it might be a Hardware failure...
- Fri Aug 20, 2010 6:58 pm
- Forum: CNC Shark
- Topic: Just Found Forum
- Replies: 3
- Views: 4539
Re: Just Found Forum
I believe a mass email went out when it started to everyone that provided an email address when purchasing a unit. Yet these antispam system seem to catch alot of stuff that you want as well as you dont.
I think we will see more and more people on here as we go into winter.
I think we will see more and more people on here as we go into winter.
- Fri Aug 20, 2010 3:52 pm
- Forum: Shark Pro
- Topic: Controller problems
- Replies: 16
- Views: 15559
Re: Controller problems
Load error usually happens because you are using the wrong post processor. When you are making the Toolpath (tap file) you need to make sure that you have selected the CNC shark on the save toolpath section of Vcarve. I have also seen this happen with a bad SD card, but since you said you changed th...
- Thu Aug 19, 2010 9:32 pm
- Forum: CNC Shark
- Topic: ALUMINUM CUTTING PROJECT
- Replies: 7
- Views: 8909
Re: ALUMINUM CUTTING PROJECT
This was done with 1/8" dia end mill at .03 depth and 30 ipm. This is a single line font.
- Thu Aug 19, 2010 8:54 pm
- Forum: Setting up the Shark
- Topic: Control Question
- Replies: 12
- Views: 15570
Re: Control Question
When tightening the setscrews on the couplers you need to use something that will keep the screw from loosening up. We use gorilla glue (just a dab will do ya) on the threads will help keep it in place but make it possible to loosen up if you need to get it off in the future. I do not recommend lock...
- Thu Aug 19, 2010 8:45 pm
- Forum: CNC Shark
- Topic: Y Axis Problem
- Replies: 9
- Views: 7236
Re: Y Axis Problem
The Y axis is the only axis connected by the end user so when Y axis problem is brought up I have the person check to make sure there are not any issues with the plug connection. But in your case this sounds like one of two problems. First the CNC Shark Basic Panel program has a limit that sounds li...