This socket error has nothing to do with feed rate - it's another issue. I suspect you have another issue buried in your system but if your happy that's all that matters.
Search found 96 matches
- Tue Jan 10, 2023 6:44 pm
- Forum: Setting up the Shark
- Topic: Troubleshooting - CNC Shark CP v2.1 Connected USB
- Replies: 6
- Views: 7086
Re: Troubleshooting - CNC Shark CP v2.1 Connected USB
- Mon Jan 09, 2023 11:21 pm
- Forum: Setting up the Shark
- Topic: Troubleshooting - CNC Shark CP v2.1 Connected USB
- Replies: 6
- Views: 7086
Re: Troubleshooting - CNC Shark CP v2.1 Connected USB
I just made another attempt as follows: Start CNCShark CP v2.1 on PC Pwr On Ctlr LED: Blue ON, Yel Blink, Red ON ... Try first just powering on the controller (don't begin with the s/w). The LEDs should indicate the same. Then check Device Manager. You should see OEMTech CNC Controller listed and n...
- Mon Dec 05, 2022 8:27 pm
- Forum: CNC Shark Pro Plus HD
- Topic: Shark HD3 Aluminum Base Track T-Nut size?
- Replies: 4
- Views: 5507
Re: Shark HD3 Aluminum Base Track T-Nut size?
These are what you want... https://www.nextwavecnc.com/shop/10-PK- ... p114869847
Then use nylon 1/4-20 bolts to fasten the spoil board down.
Then use nylon 1/4-20 bolts to fasten the spoil board down.
- Tue May 17, 2022 5:54 pm
- Forum: Software. Programming
- Topic: Tape Splitting
- Replies: 7
- Views: 5835
Re: Tape Splitting
Here's what I never understand: Why do guys like you, who figure out how to do things like this, NEVER actually include WHAT you did? Nor even where you found the solution. You're a prime culprit is this regard Rando. You post these long written solutions that actually don't most of the time give e...
- Mon Jan 11, 2021 10:14 pm
- Forum: CNC Shark
- Topic: 15 Watt Diode Laser (Not Next Wave)
- Replies: 5
- Views: 4443
- Mon Jan 11, 2021 7:23 pm
- Forum: CNC Shark
- Topic: 15 Watt Diode Laser (Not Next Wave)
- Replies: 5
- Views: 4443
- Thu Dec 17, 2020 5:32 pm
- Forum: CNC Shark
- Topic: Z Axis issues
- Replies: 9
- Views: 5214
Re: Z Axis issues
Me too Sharkcutup! Sorry, but I'll pass Rando on your Big Mouth project.sharkcutup wrote: ↑Thu Dec 17, 2020 8:44 amI have gotten my machine tuned (Feed/Speeds) for carving softwoods and hardwoods. ... Other than that I have had no real problems with the machine. I have carved many projects ...
Sharkcutup
- Tue Nov 24, 2020 6:38 pm
- Forum: Setting up the Shark
- Topic: Custom touch plate
- Replies: 9
- Views: 12241
Re: Custom touch plate
The only thing I've encountered is problems if I start running gcode when I'm not at (0,0,0). It's probably because of relative moves in g-code, rather than absolute. That's perhaps the reason Kayvon. My post command is for Absolute Mode and it pretty much dead on. I know when I was a beta tester f...
- Tue Oct 27, 2020 9:13 pm
- Forum: CNC Shark
- Topic: Z Axis Issues
- Replies: 22
- Views: 14344
Re: Z Axis Issues
Just saying... from the horses mouth!
- Sat Oct 24, 2020 8:15 pm
- Forum: CNC Shark
- Topic: Z Axis Issues
- Replies: 22
- Views: 14344
Re: Z Axis Issues
Your post implies I would need to look at getting fan in the controller box? Bill, You said you've run the job a few times before without issue. I seriously doubt heat is an issue - I'd suspect perhaps a brownout or something else gremlin like. My thoughts would be to simply monitor it going forwar...