Videos.....wow, not much help.
Moderators: al wolford, sbk, Bob, Kayvon
-
- Posts: 20
- Joined: Tue Sep 13, 2011 1:55 pm
Videos.....wow, not much help.
Thinking of making my own.
Just a thought to Rockler. I think most of us could make these in one night with our 5 year olds holding the camera.
Just a thought to Rockler. I think most of us could make these in one night with our 5 year olds holding the camera.
-
- Posts: 20
- Joined: Tue Sep 13, 2011 1:55 pm
Re: Videos.....wow, not much help.
Just to clarify...the shark rocks. does what it says it does for sure.
The videos not so much.
The videos not so much.
-
- Posts: 20
- Joined: Tue Sep 13, 2011 1:55 pm
Re: Videos.....wow, not much help.
Well,
talked with some others offline that kind of agree.
I'll see what I can do to create some better tutorials soon.
Stay tuned.
-John
talked with some others offline that kind of agree.
I'll see what I can do to create some better tutorials soon.
Stay tuned.
-John
- Consultingwoodworker
- Posts: 333
- Joined: Fri Jul 02, 2010 7:37 am
- Location: Nashville area
- Contact:
Re: Videos.....wow, not much help.
Johnny,
I created the videos to be a step by step introduction to bring a new user through their first program.
What specifically do you dislike? What would you like to see done differently? What would you do differently?
I value your feedback and that of others.
Ralph
I created the videos to be a step by step introduction to bring a new user through their first program.
What specifically do you dislike? What would you like to see done differently? What would you do differently?
I value your feedback and that of others.
Ralph
Re: Videos.....wow, not much help.
Actually I found the videos to be fairly nice. Yes, they are basic but having zero experience in the real world of CNC I needed something basic AND in small bites. I did skip doing the basic starter project just because I don't like to waste material for something I didn't need, but applied the video to my own starter project. Sure I would like to see more complex issues dealt with and more on advance features but for starting out I liked the more basic concepts to get me up to a speed I could crawl. Having them under my belt when my machine came in had me cutting within the first 24 hours.
CNC Shark HD ~ Control Panel 2.0 ~ Windows 7 & XP
Located in West Tennessee near the Tennessee River
http://www.eaglecarver4.com
Located in West Tennessee near the Tennessee River
http://www.eaglecarver4.com
Re: Videos.....wow, not much help.
The videos are OK, I would like to see on involving a bit change in the middle of a carving?Consultingwoodworker wrote:Johnny,
I created the videos to be a step by step introduction to bring a new user through their first program.
What specifically do you dislike? What would you like to see done differently? What would you do differently?
I value your feedback and that of others.
Ralph
-
- Posts: 53
- Joined: Tue Jun 19, 2012 4:24 pm
Re: Videos.....wow, not much help.
Yeah, what sk8mike said, need a video on returning to zero after a router bit change.
So I set zero for the roughing pass which is done with longer 1/4" endmill. Now I run the roughing pass and where I set zero has now been carved away. I change to a smaller ball end mill - how do I get back to zero?
So I set zero for the roughing pass which is done with longer 1/4" endmill. Now I run the roughing pass and where I set zero has now been carved away. I change to a smaller ball end mill - how do I get back to zero?
Re: Videos.....wow, not much help.
When you set up the material size in Vecric, you can use "origin offset" to move the x and y zero point off of the material block and/or out of the carving area.
You can then zero the z outside of the carved area, or on a separate block, or on the base plane of the material rather than the top. However you want to set the overal job up.
Hope this helps
Bob
You can then zero the z outside of the carved area, or on a separate block, or on the base plane of the material rather than the top. However you want to set the overal job up.
Hope this helps
Bob
Re: Videos.....wow, not much help.
Thanks for the information Bob
I never knew what the "Origin Offset was supposed to do
Cheers
Wolffie
I never knew what the "Origin Offset was supposed to do
Cheers
Wolffie
I am never going to die, I live in Paradise already
Re: Videos.....wow, not much help.
Origin Offset is intended to help with project setups on a machine that has an absolute X0, Y0 location and you want to machine a project somewhere else on the machine bed.
While it will work for this purpose, many may find it easier to use the Home Position Settings in the Material Setup form on the Toolpath tab. Simply set an X,Y position relative to the projects XYOrigin where you want to change bits and that is where the toolpath will take it after a toolpath finishes. Be sure to set your Clearance (Z1) high enough to avoid any clamps or other obstacles and this is the Z height the bit will transverse at.
Tim
While it will work for this purpose, many may find it easier to use the Home Position Settings in the Material Setup form on the Toolpath tab. Simply set an X,Y position relative to the projects XYOrigin where you want to change bits and that is where the toolpath will take it after a toolpath finishes. Be sure to set your Clearance (Z1) high enough to avoid any clamps or other obstacles and this is the Z height the bit will transverse at.
Tim