What is the maximum (ipm) X and Y axis travel speed for cutting with my Pro Plus? i seem to remember 100 ipm. The Owners Manual says: "<value>". The high speed travel speed is listed as 125 ipm.
The reason I ask is that when I use a 1/4" spiral bit at my router's lowest speed (16,000 rpm) and 100 ipm cutting rate, it SCREAMS. The recommended cure is to increase the cutting rate or decrease the RPM. The RPM can't be reduced, but if I could go higher with the travel speed, it might help.
Pro Plus travel speed.
Moderators: al wolford, sbk, Bob, Kayvon
Re: Pro Plus travel speed.
In your tool data base for the tool your using just change the feed rate to 150 instead of 100. That's what I do.
Tony
Tony
Buffalo,NY
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 11.015, photo vcarve, cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
"What will matter is not what you bought but what you built; not what you got, but what you gave”
Aspire 11.015, photo vcarve, cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.
Re: Pro Plus travel speed.
Their online manual shows the high speed positioning (jogging) rate as 120. They don't list a cutting rate but like you, I remember seeing 100 somewhere. I don't recall the colt minimum rpm but I have reduced my speeds with the 1/4" endmill to closer to 50-60 ipm otherwise I get too much flexing and the cuts aren't as good.
Re: Pro Plus travel speed.
I have a DeWALT DWP611PK router and the slowest speed is 16,000 RpM. It would be nice if I could reduce it to about 6,000 rpm, but that's just not possible with its control.
Reducing the feed rate to 50% doesn't help the noise.
If I use a V bit, the noise is much, much, less. But of course, that doesn't work for profiling.
I have the Shark 2 control panel, and use VCarve Pro 7.0.
Tonydude: Note that I have a Pro Plus. I don't believe it will go 150 ipm. That's why I was asking the question. I guess I need to run some more tests.
Reducing the feed rate to 50% doesn't help the noise.
If I use a V bit, the noise is much, much, less. But of course, that doesn't work for profiling.
I have the Shark 2 control panel, and use VCarve Pro 7.0.
Tonydude: Note that I have a Pro Plus. I don't believe it will go 150 ipm. That's why I was asking the question. I guess I need to run some more tests.
Re: Pro Plus travel speed.
NWA was selling a refurbished Pro Plus on ebay for $3300.00 and claims 200 ipm. That type of speed is tough on accuracy, especially on the non HD models.
Specs from the auction:
Enhanced controller with more power that allows up to 200 inches per min
More travel on the machine max cut of 25 x 25 x 5 inch
Automatic on and off software control of Router
Professional Aluminum case with Push button Estop.
Pendant control capability included.
Cut 3D Software Included ($300 Value!)
20 3D models, font and graphic package provided
Extended Aluminum T slot top (28-1/2" x 36") for more versatile clamping
USB interface with on controller memory storage.
Download free project plans from Vectric
Includes V-Carve 7.0 software, 1/2" dia. V-groove Bit and two hold-down clamps!
Mounts for a Bosch Router included (Router sold separately)
Free downloadable control program included
Bearings: 12 precision linear bearing guides (4 on each axis) for maximum rigidity.
Resolution: control to 0.000125 inch.
High Speed stepper motors rated at 269 oz/in
Precision modified stainless leadscrews with backlash reducing nuts on all axes.
24V Supply to provide full power to the steppers and future attachments.
One year warranty on parts and labor, special shipping exclusions apply
MADE IN USA
Specs from the auction:
Enhanced controller with more power that allows up to 200 inches per min
More travel on the machine max cut of 25 x 25 x 5 inch
Automatic on and off software control of Router
Professional Aluminum case with Push button Estop.
Pendant control capability included.
Cut 3D Software Included ($300 Value!)
20 3D models, font and graphic package provided
Extended Aluminum T slot top (28-1/2" x 36") for more versatile clamping
USB interface with on controller memory storage.
Download free project plans from Vectric
Includes V-Carve 7.0 software, 1/2" dia. V-groove Bit and two hold-down clamps!
Mounts for a Bosch Router included (Router sold separately)
Free downloadable control program included
Bearings: 12 precision linear bearing guides (4 on each axis) for maximum rigidity.
Resolution: control to 0.000125 inch.
High Speed stepper motors rated at 269 oz/in
Precision modified stainless leadscrews with backlash reducing nuts on all axes.
24V Supply to provide full power to the steppers and future attachments.
One year warranty on parts and labor, special shipping exclusions apply
MADE IN USA
Re: Pro Plus travel speed.
Check for an update. Version 7.5 is out and it is free to 7.0 users.FixitMike wrote:I have the Shark 2 control panel, and use VCarve Pro 7.0.
Re: Pro Plus travel speed.
Actually, I have version 7.508. The screen icon says 7.0.
Re: Pro Plus travel speed.
Yep, that was one thing the update routine didn't change. Easy enough to change the icon name though.FixitMike wrote:Actually, I have version 7.508. The screen icon says 7.0.