Search found 12 matches
- Mon Feb 15, 2021 12:47 pm
- Forum: CNC Shark
- Topic: Controller Replacement BlackBox
- Replies: 11
- Views: 9703
Re: Controller Replacement BlackBox
Has anyone successfully removed and replaced the NWA controller with the Openbuilds Blackbox? Now that there is a pendant available for the Blackbox it looks like a viable option. I am tossing around the idea of completely gutting the Shark electronics, motors and pendant and replacing it with the O...
- Mon Aug 05, 2019 1:45 pm
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
Thanks again to all who have taken the time to help me. I have viewed the recommended videos - they are very informative. I have been working on the urn this last weekend so I will turn my attention to the engraving today and tomorrow. I will post results and try your suggestions. I have learned a l...
- Fri Aug 02, 2019 6:58 pm
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
Kayvon wrote:Does the angle of the V bit (60-degree or 90-degree, typically) matche your VCarve tool profile?
Yes it matches the tool profile. The width and depth of the cut is wider and deeper than is shown in Vcarve's preview.
- Fri Aug 02, 2019 11:24 am
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
The bottom of all the letters are "V" shaped matching the 90 degree bit used.
It must be the lighting or angle the photo was taken that gives it a flat bottom look.
It must be the lighting or angle the photo was taken that gives it a flat bottom look.
- Thu Aug 01, 2019 1:28 pm
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
Hello and thank you for your help - I didn't get out to the shop yesterday, I needed to get some shopping and house chores done. Attached is a photo of what I get on a practice piece of MDF. I have checked and rechecked bit size, setting the z reference point using touch plate, measured the touch pl...
- Wed Jul 31, 2019 12:24 am
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
Post Processor is: CNCShark-USB Arcs (inch)(*.tap)
No change so far with the suggestions posted.
I will slow the feed in the morning and try again.
Thanks to all -
Pete
No change so far with the suggestions posted.
I will slow the feed in the morning and try again.
Thanks to all -
Pete
- Tue Jul 30, 2019 11:35 am
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
Thank you for helping me. I have zeroed out the bit at the top of the board using the touch plate. (I checked the software settings for the touch plate and it is good) I have not set up z-zero as I am using scrap plywood and that appears to be relatively flat. Do you think it's necessary? I will giv...
- Mon Jul 29, 2019 6:40 pm
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Re: Lettering Problem - Help needed
This is my first attempt at lettering.
I did a spoil board, I put through holes on 2 inch centers, surfaced it and routed lines making a two inch grid. This turned out as expected.
With this project it is my first time using V-carve/engraving toolpath tool.
I did a spoil board, I put through holes on 2 inch centers, surfaced it and routed lines making a two inch grid. This turned out as expected.
With this project it is my first time using V-carve/engraving toolpath tool.
- Mon Jul 29, 2019 12:00 pm
- Forum: CNC Shark
- Topic: Tell us where you're from map
- Replies: 617
- Views: 537255
Re: Tell us where you're from map
Marysville, WA
- Mon Jul 29, 2019 11:57 am
- Forum: CNC Shark
- Topic: Lettering Problem - Help needed
- Replies: 18
- Views: 7779
Lettering Problem - Help needed
I am a newbie to cnc routing and need some guidance please. I am making an urn and am having problems with the lettering I getting. In Vcarve pro 9.5 everything looks good, but when it is engraved on the wood I get rounded corners when they should be a straight crisp intersection. The depth of the c...