Here's my first attempt with the CNC Shark
Moderators: al wolford, sbk, Bob, Kayvon
Here's my first attempt with the CNC Shark
My first attempt with the CNC Shark. Be brutally honest - what do you think?
Re: Here's my first attempt with the CNC Shark
OK - if you know me, you know there's NO WAY I made that bench!
Just wanted to get this forum kick-started - now let's see some real CNC Shark projects!
To post, click back to "Show off your CNC Shark projects" (above) and click "Start a new topic".
Upload a picture or two, say a bit about your project, then share it with the world!
![Laughing :lol:](./images/smilies/icon_lol.gif)
Just wanted to get this forum kick-started - now let's see some real CNC Shark projects!
To post, click back to "Show off your CNC Shark projects" (above) and click "Start a new topic".
Upload a picture or two, say a bit about your project, then share it with the world!
- Consultingwoodworker
- Posts: 333
- Joined: Fri Jul 02, 2010 7:37 am
- Location: Nashville area
- Contact:
Re: Here's my first attempt with the CNC Shark
Ok, you had me worried there for a minute! LOL
-
- Posts: 1
- Joined: Wed Aug 04, 2010 2:13 pm
- Location: Thurmont, Maryland
Re: Here's my first attempt with the CNC Shark
First thought was, What part of the world do you live! Funny
Goes to show, people who own a Shark are very creative with humor also! Looking forward to a long life with this Forum. Nice Kick off! Steve
![Smile :)](./images/smilies/icon_e_smile.gif)
-
- Posts: 191
- Joined: Wed Aug 04, 2010 11:28 am
Re: Here's my first attempt with the CNC Shark
I was thinking "must have used the new 9-axis shark prototype and a really big block of wood".
Ed
![Wink ;)](./images/smilies/icon_e_wink.gif)
Ed
- CustomMadeChri
- Posts: 4
- Joined: Wed Aug 04, 2010 2:38 pm
- Location: Cambridge, MA
- Contact:
Re: Here's my first attempt with the CNC Shark
Definitely caught my attention!!
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
Re: Here's my first attempt with the CNC Shark
Hi Kim, could you send me that tool path? lol
-
- Posts: 22
- Joined: Wed Aug 04, 2010 4:23 pm
Re: Here's my first attempt with the CNC Shark
Umm yeah, here I am carving out pennstate signs thinking "FIRST ATTEMPT!? I better kick it up a notch or two!" I've made a dust collection system tha follows with the router head on the gantry. So far It has made a huge improvement. I will eventually cut the pieces on the shark. I used lexan and cherry.
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00756.jpg)
Dust foot overview
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00755.jpg)
Close up of dustfoot
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00757.jpg)
Top view removed to show construction
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00758.jpg)
bottom view. I plan on making the entry hole a little bit smaller in the future but there's no sense rebuilding untill I crash into the clamps again and destroy it. I have to add about and inch and a half on either ends of the mat'l to allow for clearance.
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00756.jpg)
Dust foot overview
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00755.jpg)
Close up of dustfoot
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00757.jpg)
Top view removed to show construction
![Image](http://i136.photobucket.com/albums/q176/stephenb79/shark%20files/DSC00758.jpg)
bottom view. I plan on making the entry hole a little bit smaller in the future but there's no sense rebuilding untill I crash into the clamps again and destroy it. I have to add about and inch and a half on either ends of the mat'l to allow for clearance.
Re: Here's my first attempt with the CNC Shark
Yeah - you'd better kick it up a notch or THREE, Stephen!
(Totally kidding).
Your "Dust Foot" is really creative! What an awesome idea!
![Wink ;)](./images/smilies/icon_e_wink.gif)
Your "Dust Foot" is really creative! What an awesome idea!
Re: Here's my first attempt with the CNC Shark
And rapiddawg: It's, um... in the mail! Yeah! ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)