Table Saw Inserts

Share your Shark projects with other forum members!

Moderators: al wolford, sbk, Bob, Kayvon

Forum rules
Do not post any files that violate copyright or licensing guidelines. Any post violating this rule will be deleted and the member may be banned from future use of cncsharktalk.
jbyers
Posts: 41
Joined: Thu Jan 05, 2012 2:35 pm

Table Saw Inserts

Post by jbyers »

Table saw inserts for VCarve. 1/2-inch Baltic Birch, 1/4-inch end mill.
Attachments
Table Saw Insert.crv
(119.5 KiB) Downloaded 1452 times
Jeff Byers
Shark Black Diamond owner since Feb-2014
Caledonia, WI

4DThinker
Posts: 951
Joined: Wed Jun 27, 2012 9:00 am

Re: Table Saw Inserts

Post by 4DThinker »

Thanks! Care to share what saw/model these were created for. Not all saws have the same blade opening.

shadetre
Posts: 8
Joined: Tue Apr 21, 2015 3:00 am

Re: Table Saw Inserts

Post by shadetre »

I would love to know what saw these inserts fit. I have a Porter Cable TS that is a PITA to make inserts for due to the construction of the thing. I have made a few but have to mill away so much material that the insert is pretty flimsy. My best solution so far is to make an insert to fir the opening in the stock plate and glue it to a piece of wood that attaches to the stock plate with rare earth magnets. Unconventional maybe but it does work pretty well.

jbyers
Posts: 41
Joined: Thu Jan 05, 2012 2:35 pm

Re: Table Saw Inserts

Post by jbyers »

Sorry gentlemen, I must have missed this request. The inserts are for a Craftsman 10-in Table Saw. Model 152.221040. I tapped some holes where they lined up with the 4 little ledges where the insert sits in the saw. I then threaded some plastic set screws that I got from McMaster Carr.
Jeff Byers
Shark Black Diamond owner since Feb-2014
Caledonia, WI

Kevink18
Posts: 205
Joined: Fri Nov 23, 2012 3:30 pm

Re: Table Saw Inserts

Post by Kevink18 »

Just bought a new grizzly and used one of mine to make a pattern to make me one. Put it on the printer scanner and than sized it by making a box the length and width than deleted box

dmyers
Posts: 72
Joined: Mon Nov 11, 2013 6:59 am
Location: Melbourne, Florida

Re: Table Saw Inserts

Post by dmyers »

Made a table saw insert for my SawStop for dado blades or egular blades for zero clearance.


table saw insert.crv3d
Saw insert fits a SawStop
(698 KiB) Downloaded 880 times

WoodEraser
Posts: 162
Joined: Fri Jul 20, 2012 7:07 am

Re: Table Saw Inserts

Post by WoodEraser »

Which model as they are different ?
Eric the "WoodEraser"
Sun City Center, Florida

If today were perfect there would be no need for tomorrow.

dmyers
Posts: 72
Joined: Mon Nov 11, 2013 6:59 am
Location: Melbourne, Florida

Re: Table Saw Inserts

Post by dmyers »

SawStop 10" contractor saw with cast iron table and 52" extension table.

dmyers
Posts: 72
Joined: Mon Nov 11, 2013 6:59 am
Location: Melbourne, Florida

Re: Table Saw Inserts

Post by dmyers »

Made a insert for my neighbors old Delta table saw, after he told me he used his dado blades with out an insert.

So I used the insert he had as a pattern and made 3 of them for him to use before he hurt himself.

Also, going to make one for another neighbor who has an old Craftsman 10" saw. Who also uses his dado blades with out an insert.

I'll upload the file when I get it done and it fits his saw.

They make cheap inserts to use to avoid tear out.

As always check all tool paths and dimensions before you cut it out.

David
delta saw insert.crv3d
Table saw insert for an older Delta 10" contractor table saw.
(496.5 KiB) Downloaded 727 times

dmyers
Posts: 72
Joined: Mon Nov 11, 2013 6:59 am
Location: Melbourne, Florida

Re: Table Saw Inserts

Post by dmyers »

Made an insert for my neighbors older Craftsman 10" contractor table saw.

As alway check dimensions and tool paths before you cut out the insert.

David
Attachments
Craftsman Table Saw Insert 1.crv3d
(1.04 MiB) Downloaded 772 times

Post Reply