Search found 36 matches
- Mon Jun 16, 2014 11:55 am
- Forum: Shark Pro Plus
- Topic: Question about making a deeper cut
- Replies: 6
- Views: 5819
Question about making a deeper cut
Hi Everyone, I am trying to make lines a little deeper in a design. I am using a 60 degree bit with the V-carve toolpath and have the depth set at .25 already. I used the toolpath in pine then in cherry ( burned a little with the cherry in the deep spots). It will make good depth at the deep spots b...
- Thu Apr 10, 2014 1:29 pm
- Forum: CNC Shark
- Topic: Tell us where you're from map
- Replies: 617
- Views: 545651
Re: Tell us where you're from map
Hi,
Tim K from Madison WI
Tim K from Madison WI
- Mon Dec 24, 2012 3:20 pm
- Forum: Shark Pro Plus
- Topic: Need help with this file
- Replies: 3
- Views: 3220
Re: Need help with this file
Thanks Bob, I didn't really know what to do with the node editing, but I played around with it and figured it out and was able the put fillets on the two corners. When I started I didn't know what size rectangle I was going to use, but next time I will figure what size rectangle and use the rectangl...
- Sun Dec 23, 2012 2:43 pm
- Forum: Shark Pro Plus
- Topic: Need help with this file
- Replies: 3
- Views: 3220
Need help with this file
Hi I am tring to put a filet on the last two inside intersections on this file so all have a .5'' deg. curve. It wont let me can someone tell me why or what I am doing wrong? Thanks Tim
- Sun Nov 25, 2012 3:47 pm
- Forum: Shark Pro Plus
- Topic: Need help with this file
- Replies: 8
- Views: 5330
Re: Need help with this file
Thanks for all help! Well I tried what you said Bob and it worked I don't know how but I changed the tool diameter to .499 and it worked. I went and ran it on the shark and it worked there too. I made two trivets ran the toolpath on one side and then flipped the piece and turned it 90 degrees and ra...
- Sat Nov 24, 2012 4:39 pm
- Forum: Shark Pro Plus
- Topic: Need help with this file
- Replies: 8
- Views: 5330
Re: Need help with this file
Here are some pictures of what is going on and my settings.
- Sat Nov 24, 2012 3:05 pm
- Forum: Shark Pro Plus
- Topic: Need help with this file
- Replies: 8
- Views: 5330
Need help with this file
Hi, I am making some trivets for christmas, with a 8"x8" piece of cherry that is .5" thick. I am making six slots with a .5" roundnose bit. Well I made a file that was .25" deep that worked great. Then I wanted it .375" deep and changed it,calabrated it and ran it again(I didn't move the piece of wo...
- Sat Nov 10, 2012 3:55 pm
- Forum: Shark Pro Plus
- Topic: Coeur'Amour box Question
- Replies: 3
- Views: 3300
Re: Coeur'Amour box Question
Hi Buc, I changed my settings to feed rate 50.0 and plunge rate to 15.0. Well I used a 1/4"up-cut bit in a test piece of wood to check it with my dowels and the hole was to big, so I used a straight bit and it made an oblong hole the whole router went forward. Do they make a drilling bit just for dr...
- Fri Nov 02, 2012 4:01 pm
- Forum: CNC Shark
- Topic: Arrow with feathers bitmap
- Replies: 2
- Views: 1897
Arrow with feathers bitmap
Hi, I can't draw at all and I am look for a arrow with feathers like in a cupid heart and arrow, but just the arrow bitmap does anyone have one or know where I can get one thanks.Tim
- Sat Oct 27, 2012 1:32 pm
- Forum: Shark Pro Plus
- Topic: Name Inlay
- Replies: 10
- Views: 8619
Name Inlay
Hi, I am trying to inlay a name (Mike) with two differant colors of wood. I have never used the inlay tool (don't know how too) but I am doing it with the V-carve engraving toolpath. I am using a 60 deg. 0.25 bit and my first cut is set at start depth 0.1 and flat depth at 0.2. On my second cut I mi...