Mach3 or Mach4

Discussion about the CNC Shark Pro Plus HD

Moderators: al wolford, sbk, Bob, Kayvon

Post Reply
big_jack
Posts: 3
Joined: Wed Nov 01, 2017 5:02 am

Mach3 or Mach4

Post by big_jack »

Need a little light. Been having problems whit cnc shark software and poor customer service . I’m running a pc in the shop, windows 10 , 64 bits. What do i need to run Mach3 or 4 on my pc and keep using my controller . What kind of connectors i will have to buy.

tonydude
Posts: 1586
Joined: Tue Aug 17, 2010 9:23 am
Location: Buffalo,NY

Re: Mach3 or Mach4

Post by tonydude »

Mach 3 and Mach 4 can't run on the shark controller.

Tony
Buffalo,NY

"What will matter is not what you bought but what you built; not what you got, but what you gave”

Aspire 12.010, photo vcarve, cut3D.cnc mako shark extended bed with the new upgraded HD 5 gantry with Led pendent.

Rando
Posts: 757
Joined: Tue Jan 06, 2015 3:24 pm
Location: Boise, ID
Contact:

Re: Mach3 or Mach4

Post by Rando »

big_jack wrote:Need a little light. Been having problems whit cnc shark software and poor customer service . I’m running a pc in the shop, windows 10 , 64 bits. What do i need to run Mach3 or 4 on my pc and keep using my controller . What kind of connectors i will have to buy.
Big Jack:

A lot will depend on how much DIY wiring you want to do. Typically no soldering or very little, but a heapin' helpin' of connectificatin'. If you're up for that....

Were I you, I'd dismantle the shark controller and grab the stepper driver modules and power supply. Scratch that. Just pull their controller and keep the rest. The nice thing is that stepper modules pretty much all work the same: power in, step and direction signals, and motor signals out. The drivers are well-tuned to the Shark hardware. Then, get one of those cheap electronics kits from a place like the below, and run either LinuxCNC, or Mach if the board is compatible. Either way, you'll be free from the silliness of the Sharks. But, you'll then be in the land of hard nose machine people. The Shark control panel is one of the simpler and more efficient to operate that I've seen. But, since you're asking about Mach, you're obviously "motivated" enough to move to that more-complicated interface. Better controllers cost more money. Don't expect a $80 controller to work like a $500 one.

These are a good example of what you can get, with I'm sure eBay having even cheaper deals: http://www.pibot.com/

Note: even THAT low-end kit has limit switches. Just sayin...

These days, 3D printers and small engraving CNCs have made controllers a commodity market. The only real challenge is making sure the power supply can drive the steppers, and that the stepper drivers can handle the current and speeds. And since we already know the stepper driver modules from the old controller are indeed so matched, that part is good-to-go. :)

Mach usually requires a parallel-port interface, which these days are had to come by, and people have migrated to a Mach-over-ethernet arrangement. So, if you get a controller that works with Mach, and put it between your PC and the stepper drivers, you'll have yourself a Cthulhu-grade Shark.

Hope that gets you on the road to a better user experience. Sorry the Shark peeps are giving you cause for grief :(.

Regards,

Thom
=====================================================
ThomR.com Creative tools and photographic art
A proud member of the Pacific Northwest CNC Club (now on Facebook)

rungemach
Posts: 460
Joined: Mon Aug 02, 2010 8:24 am
Location: Sarasota, Florida

Re: Mach3 or Mach4

Post by rungemach »

The combination of Mach3 , Smoothstepper interface (usb or ethernet), and Gecko g540 driver is a very popular and very reliable setup. Not the least expensive, but very reliable. I would not bother trying to use a PC parallel interface.

The benefits of Mach 3 are numerous, and it is a more "open" system than the Shark Controller. You can use a multitude of different manufacturer's hardware, pendants, switches, etc. Mach 3 also allows 3rd party plug-ins for added functionality. The gecko G540 drive unit is pretty much bulletproof, and allows you to fine tune your motor current per individual motor, as well as run a higher voltage supply. You can actually interface a spindle if you are so inclined. The Shark has not yet fully integrated a VFD spindle drive (to the best of my knowledge).

There may be a market for your working shark controller, for those users that want a spare and do not want to purchase a second new one.

I run Mach 3 on all my machines, and that gives me the advantage of a similar interface for everything.

Devlin
Posts: 12
Joined: Tue Dec 26, 2017 11:58 am

Re: Mach3 or Mach4

Post by Devlin »

I have been looking at putting Mach4 on my machine. And I have figured out that we need to use a completely different controller. I have been pulling teeth to find out from Nextwave as to what hardware they are using. They finally answered with.

Hi Mr. Devlin,
We use NEMA 23 Bipolar stepper motors. Any other information is company confidential that we in tech support do not know and cannot publish if we knew. We do not support Mach 4 use with our CNC machines but of course you can do what you wish with your machine.
Good luck in your endeavors.

I swear that I saw adds stating they were now using nema34. Hmmm.

So what for those who have done it would you recommend to go with for a new system. PMDX has a board that uses isolated USB for connecting.

I’m don’t like being 6 hours into a 10 hour cut and breaking a bit or whatever. With the shark you basically have to start from scratch. I want control over that.

Rando
Posts: 757
Joined: Tue Jan 06, 2015 3:24 pm
Location: Boise, ID
Contact:

Re: Mach3 or Mach4

Post by Rando »

Devlin:

As an electronics engineer, I often laugh at companies who claim that the strength of an industry-standard part is
somehow proprietary. It might be secret to THEM, and THEY might refuse to provide you that information, but it
is not at all illegal for you to ascertain, using standard and normal things, what the characteristics of the system
are. And since NWA definitely does NOT have the patent on stepper motors, your investigation and characterization
of that motor does not legally constitute "reverse-engineering". In addition, since your intention is not to compete
by selling systems that include these proprietarily-specified motors, there's zero harm, and therefore zero case.

What I'm saying is, you're free to know they're NEMA-23s somewhere in the 280-310 oz-in range, but the specific
size doesn't matter. You have to get driver modules of sufficient strength, and you have to adjust those so they
work properly with the motor IN THE SYSTEM. That means any current numbers are just a starting point, and some
small amount of tuning will be needed. (Have no fear, I have a robot-torture test for you). A single-axis 4.5A stepper
driver board from eBay, needing a 24-32/4.8A VDC supply (Amps is per-axis) will set you back about $5.

And, it's really easy to tell the motors. The two digits are the numeral and fraction of the side dimension of the face place.
So a NEMA 17 has a 1.7" square mounting face, a NEMA 23 has 2.3", and the NEMA 34s have 3.4" face plates.

The torque is variable across a range in each motor size, and motor length tends to increase as torque increases, though
there are overlaps between vendors. So, a stronger motor from mfg A might be the same size as a weaker one from
mfg B, even if mfg B makes that torque motor in a different size. The trick is when you buy them, know the mfg and
specific model number.

The thing about steppers is that they have a max torque and holding torque that at some point is independent of pushing
more current through. I'm not an expert on the underlying phenomena, but it seems like the metal rotor and stator become
magnetically saturated. That means that if your stepper driver board has a variable current-limit control (a trim-pot, nearly
all of them have them these days that I've seen), you don't REALLY care what torque you have. You have the motors you have,
and those motors have the torque they do. What YOU need to find out is how much current to drive them with. Enough to not
lose steps, but not so much as to start a fire from heat.

And for me, that testing is of an almost impossible-to-imagine, truly PERSONALLY satisfying nature. It really is. Let's assume
you're starting with a known motor + mechanicals and a variable-output, new stepper-driver board. For our size motors, a 4.5A
board (~$5 on ebay, per axis) is more than enough. Turn the current all the way UP on the driver board. Create a GCODE program
that cuts in AIR, in the same circle, over and over and over. Not a square, too much acceleration. Then let it run. For hours.
Whatever you do, do NOT put a fan on the driver board. But, DON'T touch it...a non-contact thermometer is best.

After a nice little piece, the steppers should start to heat up Watch how FAST they are heating up. If they're moving up at a
strong clip, maybe the current is too high. But, we don't really know yet. You just kinda need a feel for how quickly it's heating
up. Let that run around in circles until one of these things happens:

1) everything overheats and fails: turn down the current a little and try again. No, you don't need to let it cool down, unless
it's somehow still not working after the adjustment;

2) The motor reaches 125C (257F)...see, I told you not touch it!...that's good, but only a little bit too hot. turn the current
down just a smidge and leave it there. The plastic, HDPE is good until 200C+, so the motor isn't going to harm it. Inside the
motor is magnet wire in 260C (500F) epoxy-enamel insulation, held in place on a stationary aluminum structure, protected in
nylon (250C melting) coil-holders. 125C (257F) is not going to hurt anything.

3) The stepper driver board somehow reaches over 85C: stop immediately and lower the current a significant amount. This
would indicate that the driver is not strong enough to drive the motor. If it's a real 4.5A driver, it'll be a module about 2x3.2"
with a good, beefy heatsink. If it's a lot smaller than something that size, then be cautious.

4) After about 15 minutes, the stepper motor and drivers settle in, reasonably above 60C, and below 100C. In that case, you've
got it dialed in and it should be quite reliable.

5) Things lose steps, the cutting starts to drift, and the movement doesn't seem "crisp": you know what to do :D Give it some
more juice.

Add a fan to those driver modules, and it should be fully reliable on all cuts, even hours-long ones. The motors should stay below
100C, and the drivers should stay not much more than the 70C. With a decent electronics-fan, the heatsink should be in the 50C
and under range. Of course, be careful that the fan doesn't pack your electronics with dust...or in my case, fine aluminum chips.

=================================

I've been doing some engineering with steppers these days, and I can tell you these things:

Our motors are NEMA 23, in the 285-300 Oz-in class. How can I tell? Because the next step up in torque, in the 430 oz-in
range, requires drivers that put out 4.0-4.5A. Given the size of chip and heatsink provided in current drivers that CAN
handle that current, and given the size and amount of heatsinking that our modules actually DO have, there is no way
they can push 4.5A, and therefore would be horribly under-driving the larger size. Thus, they must be somewhere in the
280 oz-in range for a NEMA 23 stepper. Those motors tend to take 2.8-3.5A, which is just the right amount for the chips
and heatsink size we have in our controllers. Don't just go on coil resistance, however, since they use different size wire
AND different number of wire loops ("turns" in the vernacular) in the different motors.

I'm too am currently investigating replacing my controller, but in my case with a LinuxCNC unit. Total controller cost without
the old PC is on the order of a couple hundred bucks, with the main parts coming in ~$60-75. Mine's a little strange because
I intend to actually embed the Shark controller board, minus the driver modules, into the new controller. I have a lot of already-
verified toolpaths that I don't really want to re-engineer. :roll:

The shark controller won't work with Mach....if you want to use Mach, expect to put in a new controller. If you want to
run Mach on Windows 7, you can use Mach 3 and a PCI-X (or PCI) add-in parallel port. However...and this is important:
in you want to run Windows 8 or Window 10 with Mach, you can only run Mach 4, and you can only use the Ethernet
smooth-stepper interface boards. Why? Because Windows 8 and Windows 10 changed how application software (like Mach)
accesses hardware. And direct parallel-port access is now forbidden.

LinuxCNC doesn't have those Windows restriction, however it does run on Linux, which can be confusing for some.
That said, both the OS and CNC controller software are FREE, and the LinuxCNC community is updating and fixing the
software FAR more frequently than do the Mach people.

Hope that helps. You can contact me via private-message, or email thom at thomr dot com if you're interested in more
details on the controller(s) I'm putting together.

Regards,

Thom Randolph
Last edited by Rando on Mon Jun 11, 2018 9:20 pm, edited 1 time in total.
=====================================================
ThomR.com Creative tools and photographic art
A proud member of the Pacific Northwest CNC Club (now on Facebook)

Devlin
Posts: 12
Joined: Tue Dec 26, 2017 11:58 am

Re: Mach3 or Mach4

Post by Devlin »

They sterilized the motors. Stickers removed. But I’ll have to check dimensions to verify nema. Thank you. I’m looking to keep the shark pretty much intact and put a new controller on it. Would like to do a setup that I can upgrade a home built onto later. That way I can put the shark back together as original.

User avatar
Kayvon
Posts: 560
Joined: Tue Oct 21, 2014 11:46 pm

Re: Mach3 or Mach4

Post by Kayvon »

Wow, Thom. I'm catching up after being gone for a while. That's the best post I've seen so far. So much good info. I've added that to my notes. Maybe it'll be useful for a future project or fix.

Rando
Posts: 757
Joined: Tue Jan 06, 2015 3:24 pm
Location: Boise, ID
Contact:

Re: Mach3 or Mach4

Post by Rando »

Kayvon wrote:Wow, Thom. I'm catching up after being gone for a while. That's the best post I've seen so far. So much good info. I've added that to my notes. Maybe it'll be useful for a future project or fix.
Thanks, man. Many of my co-workers have commented about my support-request responses that "he certainly never leaves anything out." ;-).

Cheers!
=====================================================
ThomR.com Creative tools and photographic art
A proud member of the Pacific Northwest CNC Club (now on Facebook)

Post Reply